Rahul Trading Company

Description:-
Conplast SP500 is based on Sulphonated Napthalene Polymers and is supplied as a brown liquid instantly dispersible in water.

Main uses

• Conplast SP500 has been specially formulated to give high water reductions up to 25% without loss of workability or to produce high quality concrete of reduced permeability.

Advantages

• Improved workability - Easier, quicker placing and compaction.
• Increased strength - Provides high early strength for precast concrete if water reduction is taken advantage of.
• Improved quality - Denser, close textured concrete with reduced porosity and hence more durable.
• Higher cohesion - Risk of segregation and bleeding minimised; thus aids pumping of concrete.
• Chloride free - Safe in prestressed concrete and with sulphate resisting cements and marine aggregates.

Description:-
Renderoc HB40 Plus is an extra high build, shrinkage compensated repair mortar conforming to EN1504-3 Class R3, compatible with concrete 25 - 50 MPa. For the reinstatement of concrete where low permeability and high resistivity characteristics are key requirements.

Typical Applications

• Vertical & overhead patch repairs
• Localised trowel or wet spray application, up to 1m2 repair area
• Trowel build depth between 10-40mm required, and a required strength is between 25-50 Mpa. Higher build & improved application compared to HB40

Advantages

• Compatible with concrete strength in the range 25 to 50 MPa
• High strength - suitable for structural repairs
• Abrasion resistant - suitable for aggressive environments
• Shrinkage compensated - provides long term dimensional stability
• Low permeability to potentially damaging water, CO2 and chloride ions
• High build formulation - fewer applications of product
• High resistivity - provides increased durability
• Excellent bond to SSD concrete substrates ? no separate primer required in most circumstances - refer to Substrate Priming section of TDS
• Can be applied using wet-spray process - providing faster high build repairs
• Pre-bagged to overcome site-batched variations - only the site addition of clean water required
• Sustainable product with lower carbon foot print - formulation based on supplementary cementitious materials
• Complies to EN 1504-3 Class R3

Key Properties

• 28 day Strength : 50 Mpa
• Application : Trowel, Wet Spray
• Certifications/conforms to : RMS B80
• Compatible concrete strength : 25-50MPa
• Suitable for use with Galvashield anodes: No
• Trowel Build / Depth : 10mm to 100mm vertical

Description:-
Brushbond TGP is an economical cementitious coating system designed for waterproofing concrete against low positive or negative hydrostatic water pressure in a wide variety of structures such as.

Main uses

• Sewage treatment and water treatment plants
• Water tanks
• Concrete pipes
• Manholes

Advantages

• Penetrates concrete, seals capillary tracts and hairline cracks
• Contains no chlorides
• Easy to apply, cost effective in use
• Can be applied to new or old concrete in both interior and exterior locations
• Suitable above or below ground
• Surface damage will not affect the system.

Renderoc RG is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a free-fl owing non-shrink repair micro concrete. The material is based on Portland cements, graded aggregates and fi llers, and additives which impart controlled expansion characteristics in the plastic state, while minimising water demand. The low water requirement ensures high early strength and long-term durability.

Main uses

• For larger repairs, the mixed Renderoc RG may be modified by the addition of 5mm to 12mm clean, graded, saturated surface dry aggregates at site. For exceptionally large repairs, the local Fosroc office shall be consulted.

Advantages

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state.
• Can be pumped or poured into restricted locations.
• Highly fluid to allow for placement without vibration.
• Pre-packed to overcome site-batched variations.
• Rapid strength gain to facilitate early reinstatement.
• High ultimate strengths and low permeability of cured repair.
• Contains no chloride admixture.

Description:-
Brushbond is a cementitious coating for application to concrete and brickwork to provide a waterproof barrier and fiil out surface imperfections.

Main uses

• Suitable for sealing water tanks,reserviors,toilets and bathrooms,balconies and basements as well as filling blowholes,cracks,imperfections and for providing concrete surfaces with a uniform appearance.

Advantages

• Minimum surface preparation needed
• Excellent adhension.Bonds directly to porous and non- porous surfaces
• Waterproof and non-toxic-Ideal for potable water tanks
• Excellent for damp-proofing basements below ground
• Breathable-Allows transmission of water vapour from interior of building
• High resistance to carbon dioxide and chloride ion diffusion
• Can fill the honeycomds, dot surfaces and concrete with potholes

Description:-
Integral waterproofing admixture based on crystalline formation to produce water tight concrete.

Main uses

• Conplast Crystalline is an integral waterproofing admixture to produce water tight concrete. The active chemical in Conplast Crystalline react with moisture available in concrete to produce non soluble crystalline formation throughout the pores of capillary tracks thus making concrete permanently sealed against water penetration from any direction.
• Conplast Crystalline is developed to use in
• Water reservoir
• Tunnel concreting,
• Retaining walls and subways
• Water tank and swimming pools
• Precast unit

Advantages

• Easy to use, require only mixing with concrete.
• Integral waterproofing system.
• Crack filling property with time up to 0.4mm width.
• Exhibits good resistance to hydrostatic water pressure
• both surface.
• Compatible with our full range of water reducing
• admixture.
• Most effective due to formation of crystalline in tiny
• capillaries.
• Increase durability.

Description:-
Hydroproof Xtra is formulated to be mixed with cement on site or simply brush applied over concrete or masonry surfaces to provide an effective waterproof membrane.

• Non - toxic, non-fl ammable and user friendly
• Provides a tough, impermeable waterproof membrane
• Can be applied by brush, on horizontal and vertical surfaces
• Excellent adhesion to concrete and masonry surfaces
• Protects concrete and mortar from natural elements such as wind, rain, sunlight
• Breathable - allows inside water vapour to escape.
• Also Available in 20 L(Price:-4300 ).

Description:-
Renderoc Plug is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent, rapid setting mortar which is easy to apply in many difficult conditions.

Main uses

• For the rapid patching and plugging of concrete segments, concrete and brick tunnel linings, sewage systems, below ground access chambers, pipes, basements, foundations and mines.

Advantages

• Emergency water-stopping capability.
• Single component.
• Excellent bond to the substrate.
• Low exotherm minimises thermal cracking.
• Pre-bagged formulation to overcome variations in site batching.
• Chloride free
• Renderoc Plug 20: Approved for use in public water supplies
• Renderoc Plug 20: BS6920 listed product

Description:-
Reebol:-To provide quick, clean and easy stripping of moulds and formwork and ensure high quality, fair faced and stain free concrete.

Main uses

• Ensure even concrete surface
• Reduces opportunity of damage to formwork, extending usable life.
• Minimises cleaning of formwork before re-use
• Suitable for use with virtually all types of formwork.
• Inhibits corrosion of steel formwork.

Description:-
Integral waterproofing liquid admixture for concrete, plaster and mortars.

Main uses

• To minimise permeability and increase the waterproofing properties of concrete, plaster and cement sand mortars for critical applications like roof slabs, screeds, basements, external plastering, bathroom floors, water tanks, sumps, drains etc.

Advantages

• Advanced Technology : New generation molecule yields high performance concrete. Suitable for any grade of concrete including higher grades.
• Corrosion resistant: Meets the requirements of Japanese code JIS Z1535 (modified) first of kinds in the integral water proofing range.
• High Strength : Due to better dispersion of cement particles and helps in the better degree of hydration yielding high strength compared to control.
• Cohesive Mix : Improves workability and cohesiveness of the concrete.

• Durability : Improves durability due to reduction in permeability of concrete and corrosion resistance of steel.
• Also Available in 50 L (Price :-3200).

Description:-
Cebex 100 is supplied as a powder admixture. The material is a combination of a plasticising agent and a gas producing expansion medium.
The plasticising agent allows the use of a reduced water/cement ratio with consequent increased strengths and durability. The expansive medium counteracts the natural settlement and plastic shrinkage of the grout and aids stability and cohesion.

Main uses

• Sufficient restrained expansion is developed to ensure a high degree of inter facial contact.
• Gaseous expansion system compensates for plastic shrinkage and settlement in properly designed cementitious grout.
• Reduced water/cement ratio in the grout mix ensures low permeability and long term durability in service.
• Gives high grout fluidity with low water/cement ratio, thus making placement or injection of the grout easy.
• No metallic iron content to corrode and cause staining or deterioration due to rust expansion in the grout.
• Composition allows high early strength development in grouts, without the use of chlorides.

Advantages

• Gaseous expansion system compensates for plastic shrinkage and settlement in properly designed cementitious grout.
• Reduced water/cement ratio in the grout mix ensures low permeability and long term durability in service.
• Gives high grout fluidity with low water/cement ratio, thus making placement or injection of the grout easy.
• No metallic iron content to corrode and cause staining or deterioration due to rust expansion in the grout.
• Composition allows high early strength development in grouts, without the use of chlorides.